design a chain conveyor drive with a conical-cylindrical reduction gear.
- Added: 08.10.2019
- Size: 2 MB
- Downloads: 0
Description
Components of the drive are: electric motor, conical - cylindrical reduction gear, 2 elastic couplings, drive shaft. The drive operates as follows: torque is transmitted from the electric motor through an elastic clutch to the input shaft of the reduction gear box; from output shaft of reduction gear box through elastic clutch to drive shaft. It is required to perform the necessary calculations, select the best parameters of the diagram and develop the design documentation intended for the manufacture of the drive: • gearbox general view drawing (at the stage of sketch design); • gearbox assembly drawing (at the stage of engineering design); • working drawings of gearbox parts; • gearbox general view drawing; • design explanatory note and specifications;
Project's Content
|
|
KOMPAS - Спецификация ДМ1.pdf
|
KOMPAS - Спецификация ДМ2.pdf
|
Колесо листа 4.cdw
|
кур проект.docx
|
Лист 1и 2.cdw
|
Лист 3.cdw
|
Лист 5.cdw
|
Муфта листа 4.cdw
|
Тихоходный вал листа 4.cdw
|
Additional information
Contents
Contents
Introduction
1. Kinematic calculation
1.1 Electric motor selection
1.2 Determination of rotation speeds and moments on shafts
2. Calculation of cylindrical gear train
2.1. Preparation of initial data for computer calculation
2.2.Analysis of computer calculation results and selection of option for design study
3. Preliminary Shaft Calculation
3.1. High-speed shaft (pinion shaft)
3.2 Intermediate shaft
3.3. Slow-moving shaft
3.4 Distances between gear parts
4. Bearing Type Selection and Calculation
4.1. Select Bearing Type
4.2 High speed shaft
4.3 Slow-moving shaft
4.4 Intermediate shaft
4.5 Drive shaft
5. Gear Design
5.1. High speed gear:
5.2. High-speed stage wheel:
5.3. Low-speed gear:
5.4. Low-speed stage wheel:
6. Calculation of connections
6.1.Connection of gearbox intermediate shaft with wheel
6.2.Connection of gearbox output shaft and coupling
6.3.Connection of drive shaft and coupling
6.4. Calculation of connections with interference. Selection of landings
7. Design of housing parts and bearing covers
8. Calculation of shafts for strength
8.1 High speed shaft
8.2 Slow-moving shaft
8.3 Intermediate shaft
8.4 Drive shaft
9. Selection of lubricants and lubrication system
10. Calculation of couplings
10.1 Elastic coupling with torus-shaped shell
10.2. Selection and check calculation of elastic coupling with rods
10.3. Check calculation of combined coupling
List of literature used
Introduction
The purpose of this project is to design a chain conveyor drive with a conical-cylindrical reduction gear.
Components of the drive are: electric motor, conical - cylindrical reduction gear, 2 elastic couplings, drive shaft.
The drive operates as follows: torque is transmitted from the electric motor through an elastic clutch to the input shaft of the reduction gear box; from output shaft of reduction gear box through elastic clutch to drive shaft.
You need to perform the necessary calculations, select the best diagram parameters and develop design documentation for the manufacture of the drive:
• gearbox general view drawing (at sketched design stage);
• gearbox assembly drawing (at technical design stage);
• working drawings of gear box parts;
• general view drawing of the drive;
• calculation and explanatory note and specifications;
Колесо листа 4.cdw
Лист 1и 2.cdw
Лист 3.cdw
Лист 5.cdw
Муфта листа 4.cdw
Тихоходный вал листа 4.cdw
Similar materials
- 15.02.2021
- 02.10.2019