Front head of table lathe
- Added: 07.11.2019
- Size: 1 MB
- Downloads: 0
Description
The front head of the table lathe is designed to transfer rotation from the engine to the machined part. Rotation is transmitted to two-stream pulley 2 by wedge-belt transmission. Rotation from pulley 2 to machined part is transmitted by two carriers 3. Pulley 2 is connected to axle 13 by key 19 and attached to axle by screw 16. Axle 13 rotates in two ball bearings 18, one of which (right) is fixed in housing 1 with thrust ring 11 with screws 15 and nut 8. Bearings 18 are wound with thick lubricant laid inside housing 1. The ring 17 protects the lubricant from flowing out of the housing and protects the bearings 18 from dust and dirt. Front head is installed on guides of machine and fixed on them with eccentric clamp, then eccentric 6 is fixed by turning. Archive Composition - 3D Part Models and Assembly
Project's Content
|
И00.73.00.01 _ Корпус.m3d
|
|
И00.73.00.02 _ Шкив.m3d
|
|
И00.73.00.04 _ Шайба.m3d
|
|
И00.73.00.05 _ Прижим.m3d
|
|
И00.73.00.06 _ Эксцентрик.m3d
|
|
И00.73.00.07 _ Пружина.m3d
|
|
И00.73.00.08 _ Гайка.m3d
|
|
И00.73.00.09 _ Прокладка.m3d
|
|
И00.73.00.10 _ Втулка.m3d
|
|
И00.73.00.11 _ Кольцо упорное.m3d
|
|
И00.73.00.12 _ Втулка распорная.m3d
|
|
И00.73.00.13 _ Ось.m3d
|
|
И00.73.00.14 _ Крышка.m3d
|
|
Кольцо СГ 32-21-3,5 ГОСТ6418-67.m3d
|
И00.73.00.00 _ Бабка передняя настольного токарного станка.a3d
|
И00.73.00.00 _ Бабка передняя настольного токарного станка.spw
|
2019-11-07_190248.jpg
|
Additional information
И00.73.00.01 _ Корпус.m3d
И00.73.00.02 _ Шкив.m3d
И00.73.00.04 _ Шайба.m3d
И00.73.00.05 _ Прижим.m3d
И00.73.00.06 _ Эксцентрик.m3d
И00.73.00.07 _ Пружина.m3d
И00.73.00.08 _ Гайка.m3d
И00.73.00.09 _ Прокладка.m3d
И00.73.00.10 _ Втулка.m3d
И00.73.00.11 _ Кольцо упорное.m3d
И00.73.00.12 _ Втулка распорная.m3d
И00.73.00.13 _ Ось.m3d
И00.73.00.14 _ Крышка.m3d
Кольцо СГ 32-21-3,5 ГОСТ6418-67.m3d
И00.73.00.00 _ Бабка передняя настольного токарного станка.spw
Similar materials
- 29.05.2022
