Чертежи и схемы гитары Fender Telecaster различных моделей
- Добавлен: 26.04.2026
- Размер: 3 MB
- Закачек: 0
Описание
Состав проекта
|
53BODYMASTERNSNOFLAT2.dwg
|
|
tele pickguard.dwg
|
tele body and pickguard.pdf
|
Tele outline wLayers rotated revB METRIC.dxf
|
NECKSOLIDS1.X T
|
72 tele deluxe pickguard.pdf
|
|
Thinlines.pdf
|
|
NECK50SFINAL2D.DXF
|
|
BROADCASTER NECK.pdf
|
|
53BODYMASTERNSNOFLAT1.DXF
|
|
Thinline[1].pdf
|
Tele outline wLayers rotated revB METRIC.dwg
|
|
tele body drawing revD.pdf
|
|
tele scratchplate pdf.pdf
|
|
pick guards.pdf
|
|
telecaster 4.pdf
|
|
modified 72 guard final.dwg
|
|
NECK.pdf
|
|
modified 72 guard.dwg
|
|
fender headstocks.pdf
|
|
72 Custom - Deluxe.pdf
|
|
Tele body drawing revD.dwg
|
|
1.6875 am head[1].pdf
|
|
69ThinlineReissue outline.pdf
|
- AutoCAD или DWG TrueView
- Adobe Acrobat Reader
Дополнительная информация
72 tele deluxe pickguard.pdf
are true to scale. If you experience problems with the PDF send a Self Addressed Stamped envelope with your written request
for a tracing or print of the template we have on file to: Terrapin Guitars LLC PO Box 11565 Eugene OR 97440
PDF011109-T72D-WRH-WRH-1234TGL
Thinlines.pdf
where file was posted
the area around the f hole
on the inside of the cap is
routed to a thickness of 18
so that the edges of the cutout
aren’t the full thickness of the cap
the control route has solid walls
- no chamber in this area unless you design it otherwise.
for balance weight here might be a good thing.
because of the way the jack hole hits the control route
you may want to consider drilling the jack hole before routing.
with a 78 bit and a hand drill it’s a potential wrist twister
when the bit hits the open area on one side.
with a drill press it will put your clamping to the test.
it scaled showing .3 and .6 radii being used.
redrawn here to show that either 1.125 or 1.25
and .625 drill bits work just as well.
Classic Player Thinline
otherwise it’s back access with cover
the control hole in the cap is an approximation
p’up wiring channels on body only - not topcap.
when gluing on the top having it face down will
keep excess glue from running down the sides
of the chambers and channels
if putting a switch here
word has it that you can fish mini pots in after the cap in glued on and the body finished.
place pots and switch for looks or to fit your hands
Tele outline wLayers rotated revB METRIC.dwg
pick guards.pdf
for a .09” 3 ply just file
Deluxe with Tele neck pocket
Classic Player Thinline
fender headstocks.pdf
James Burton (3 p’up)
James Burton Standard
th Anniversary Golden
Hwy-1 Showmaster HSS
Highway 1 (US Special)
both drawn with locking nut
Richie Sambora Mex Std
Mex Std Fat Strat - FR
Jimi Hendrix Tribute
oddity: tuner holes moved outward
the 24.75 scale telesonic was drawn with the std positioning
oddity: tuner holes moved up and out
oddity: tuner holes set on
degree angle instead of 17
72 Custom - Deluxe.pdf
the guard needs to be modified around the
tremolo - see pickguards and classic player
Deluxe with Tele Neck Pocket - P90s shown in routes - marked for either a hardtail or tremolo
a file and sandpaper wrapped
around a 12 drill bit to modify
a store bought pickguard
if using a tremolo the guard also
needs to be filed around the
bridge plate - see pickguards
if you want P90 pick guard tight and even get the pickup first and measure
I believe I heard Lollar say that he can send a template for the pickguard with
WRHB center line for back p’up = same for
humbucker in the tele humbucker bridge plate
custom HH teles use same
center line for the neck as
the WRHB same for the
mini-humbucker uses front edge of tele route.
in a youtube vid Lollar does the same with the CC p’up
Custom HH teles have the bridge
p’up slightly forward
Click here to go to TDPRI
where file was posted
block and use 12” router bit
or drill to fit the toggle of your choice
as drawn the pocket is sized to leave
a 0.017” gap around the neck to allow for
the thickness of the finish on both the neck
and body. The pick guard is drawn .012
from the pocket and .005 from the neck.
-38 deep to cover the jack hole
The inside corner radius of the pocket is
drawn as .267 (.25R of the neck + 0.017)
The pickguard is drawn with the same .25
radius as the neck.. but .01 wider.
All of the above exists only in the world of
CAD where you can zoom in and CNC.
WRHB routes and channels are the same depth
as the neck pocket (which is usually around 58ths 116th shallower for higher action and vice versa)
25 p’up route corner radius from .5 bit
Ideally it’d make sense to have the channel and
p’up routes on the neck route template but
it might make more sense to have the deeper switch
and control routes on the neck pocket template and
p’up and channel routes on the body template as the
neck p’up routes are very close to the neck pocket and
could make for a weak area on the template.
either way you’ll want to route the deeper first then
the shallow (unless you want to make plugs to fill the
existing shallow routes when routing the deeper)
267 R = 0.534 D. 732 drill bit = 0.531250
tick marks are for a 165 nut neck
but even a 1.65 nut neck probably
won’t be excactly on when you
put straight edge to it’s sides
Using them as reference points
should get it fairly straight.
if you have the neck in hand to block on
the template cheap masking tape is about
005” (5 mils). A few layers on the neck
before blocking will give you a gap
outer holes 38ths in from
It could be that you end up switching templates a couple of times.
outer holes 0.4” from
Tele body drawing revD.dwg
NOMENCLATURE OR DESCRIPTION
NOTES: UNLESS OTHERWISE SPECIFIED:
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
PLACE DECIMALS ±.010
REMOVE ALL BURRS AND SHARP EDGES
CONCENTRICITY MACHINED DIAMETERS .010 FIM
DIMENSIONAL LIMITS APPLY BEFORE PROCESSES
HOLE DIAMETER TOLERANCE
INTERPRET DRAWING PER DOD-D-1000
PARENTHETICAL INFO FOR REF ONLY
104 DIAn0.75 DPn2 PL
CONTROL CAVITYn1.50 DP
NECK POCKETn0.625 DP
PICKUP POCKET 0.850 DP
PICKUP POCKET 0.687 DP
109 DIAn0.75 DPn4 PL
ALL DIMENSIONS ACROSS CENTERLINE ARE SYMMETRICAL TO CENTERLINE
LEFT-HAND BODY IS DIRECT OPPOSITE OF RIGHT HAND. LEFT HAND BODY CAN BE MADE BY REVERSING TOOLING.
OUTLINE CONTOUR TO BE TAKEN FROM THIS DRAWING
THE DRAWING IS FOR REFERENCE ONLY AND DOES NOT GUARANTEE ANY DIMENSION TO MATCH ANY EXISTING MODEL WITH ACCURACY
125 R NECK SOCKET AREA ONLY
125 R BOTH SIDESnEXCEPT NECK SOCKET AREA
CHANGED BODY R TO 0.125 NECK
PKT TO 58 CNTRL CAVITY TO 3.125
CORRECTED BRIDGE PICKUP RADII
ADDED NECK POCKET RADII
166 DIAn82 DEG CSKn.025 DIA FARSIDEn4PL
REMOVED 0.687DP FROM BRIDGE
ADDED HOLE SPEC TO NECK POCKET
ADDED DEPTH TO WIRING CHANNEL
TELECASTER IS A REGISTERED TRADEMARK OF THE FENDER MUSICAL INSTRUMENT CORPORATION
Рекомендуемые чертежи
- 24.01.2023
- 25.01.2023
